Search found 67 matches
- Wed Aug 03, 2011 1:50 am
- Forum: Technical Support
- Topic: GV Callback Problem
- Replies: 8
- Views: 2001
Re: GV Callback Problem
Hello, Aaron. I use Sipgate and IPKall. The problem occurs with both of them. When a callback fails I'll usually wait a few seconds and then place it again using a different provider until it connects. So, I've experienced the problem with both providers and both during the same call attempts as well.
- Tue Aug 02, 2011 9:04 pm
- Forum: Technical Support
- Topic: GV Callback Problem
- Replies: 8
- Views: 2001
GV Callback Problem
Sometime over the past couple of weeks a problem has arisen with GV callback. Often times the initial SS ring doesn't switch to the callback ring, yet the callee's phone will ring. Then, after a few more tries. a successful call is placed to a frustrated friend. I've gotten used to occasional callba...
- Sun Feb 14, 2010 8:00 pm
- Forum: Use Cases
- Topic: Phone-Controlled Google Voice Outbound Dial Plan
- Replies: 11
- Views: 8686
A new feature, Pseudo 2-Line Phone , has been added to the dial plan. As described in the main post, it allows dialing out on a second Google Voice account. While this feature is only useful for those who have two Google Voice accounts, two accounts are not required to use the dial plan. To implemen...
- Mon Feb 08, 2010 9:05 pm
- Forum: Report a bug
- Topic: Database Not Working Properly
- Replies: 3
- Views: 1290
Same here. I'm getting the following log messages when performing reads/writes:
Code: Select all
Exception DBRead. Format of the initialization string does not conform to specification starting at index 0.
Exception DBWrite. Format of the initialization string does not conform to specification starting at index 0.
- Wed Feb 03, 2010 9:56 pm
- Forum: Technical Support
- Topic: Symmetric NAT with Cisco 7965
- Replies: 47
- Views: 32408
I'm not familiar with your device, but I glanced at the documentation and there is a setting to enable NAT mapping, which I'm guessing you've already enabled. What I didn't readily notice in the documentation is a setting for NAT Keep Alives. If this is the case, you may want to try enabling Keep Al...
- Wed Feb 03, 2010 6:27 pm
- Forum: Report a bug
- Topic: SIP1 Down / SIP2 Misbehaving
- Replies: 8
- Views: 2506
- Wed Feb 03, 2010 6:31 am
- Forum: Report a bug
- Topic: SIP1 Down / SIP2 Misbehaving
- Replies: 8
- Views: 2506
- Wed Feb 03, 2010 4:51 am
- Forum: Report a bug
- Topic: SIP1 Down / SIP2 Misbehaving
- Replies: 8
- Views: 2506
- Tue Feb 02, 2010 7:46 pm
- Forum: General VoIP Discussions
- Topic: Private Caller -> Nashville CID = IPKall?
- Replies: 1
- Views: 1543
Private Caller -> Nashville CID = IPKall?
In the past couple of days I received a few calls with a CID of 16157247999 Nashville, TN. I initially thought they were junk calls because the first one gave a dial tone when picked up, but since then, I think I figured it out to be a CID problem applied only to unknown/private callers and intermit...
- Mon Feb 01, 2010 9:27 pm
- Forum: Technical Support
- Topic: Help Needed on SIP URI Dialing
- Replies: 7
- Views: 2354
Here is some Ruby gsub documentation . /%(..)/ is a regex pattern that will match a run of characters beginning with a percent sign followed by any two characters. The parenthesis capture the two characters following the percent sign and they are available to the block (the code within the curly bra...