Please Help With Dialing Plan
Please Help With Dialing Plan
I Have Multiple Sip Providers, But I Only Need A Outbound Dialing Plan For One, If you Can Who Ever Would Like To Help Takes A Look At This Service Provider, They Allow Outbound Calls To Landline, http://www.voipcheap.com. Any ways when i dail out i want to be able to call landlines using this provider, list of my provider are, gizmo1, gizmo2, voipcheap1, and voipcheap2, i'm trying to dial out using voipcheap1 and voipcheap2.
Hi, using Sipsorcery, for outbound calling with betaproviders, like Voipcheap is, will give you no FUP, because you share the IP address of the Sipsorcery, with al Sipsorcery users, and this will be noticed by Voipcheap in your case.
There are already many posts posted on this subject on the Mysipswitch forum, about constructions, with the combination of Voxalot....
If that setup is to complicated for you to setup, you should have Voipcheap registering on your own ATA/voip device, for outbound calls, maybe more if used on gw1, gw2, settings ?
You should mention which ATA you use, this matters a lot....
Also, where most contacts are, who you need to contact, there are more constructions possible....
btw.
normally, you don't have to register your ata for outbound calls, but for FUP with betamax providers you do, check this for your self, otherwise you save your self a lot of trouble.
btw.2
You can't fool betamax providers by using 2 accounts, same issue, 2 accounts on same IP address....
There are already many posts posted on this subject on the Mysipswitch forum, about constructions, with the combination of Voxalot....
If that setup is to complicated for you to setup, you should have Voipcheap registering on your own ATA/voip device, for outbound calls, maybe more if used on gw1, gw2, settings ?
You should mention which ATA you use, this matters a lot....
Also, where most contacts are, who you need to contact, there are more constructions possible....
btw.
normally, you don't have to register your ata for outbound calls, but for FUP with betamax providers you do, check this for your self, otherwise you save your self a lot of trouble.
btw.2
You can't fool betamax providers by using 2 accounts, same issue, 2 accounts on same IP address....
Thanks, The Fug.
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
I have all 800 numbers going to sipbroker and all else goes to voxalot. Voxalot sends calls to Betamax.
My Dialplan
https://www.mysipswitch.com/forum/viewt ... =8122#8122
TheFug's
https://www.mysipswitch.com/forum/viewt ... ight=#8201
My Dialplan
https://www.mysipswitch.com/forum/viewt ... =8122#8122
TheFug's
https://www.mysipswitch.com/forum/viewt ... ight=#8201
Last edited by sirmikey1 on Thu Jul 09, 2009 7:44 pm, edited 1 time in total.
I had to dig in the forum: http://tinyurl.com/mz798y
Thanks, The Fug.
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
Thanks you for all the post, so far here my dialing plan.
#Ruby
# Dial Plan Generated by Rubyzard v0.1
# If you need help, please post in our forum
# http://www.mysipswitch.com
# SIP tracing : true or false
sys.Trace = false
sys.Log("call from #{req.Header.From.FromURI.ToString()} to #{req.URI.User}.")
if sys.In then
# Do your INCOMING call processing customisations here.
sys.Dial("sip:shawndellh@sip.VoipCheap.com",30)
sys.Dial("0017086839331@VoipCheap1",30)
sys.Dial("17086839331@VoipCheap1",30)
sys.Dial("17086839331@VoipCheap1",30)
sys.Respond(480, "#{sys.Username} Not available")
else
# Do your OUTGOING call processing customisations here.
case req.URI.User
when /^00/ then sys.Dial("1${dst:2}@VoipCheap1")
when /^1*/ then sys.Dial("VoipCheap1")
when /^00/ then sys.Dial("VoipCheap1")
else sys.Dial("VoipCheap1")
end
end
# Dial Plan Generated by Rubyzard v0.1
# If you need help, please post in our forum
# http://www.mysipswitch.com
# SIP tracing : true or false
sys.Trace = false
sys.Log("call from #{req.Header.From.FromURI.ToString()} to #{req.URI.User}.")
if sys.In then
# Do your INCOMING call processing customisations here.
sys.Dial("sip:shawndellh@sip.VoipCheap.com",30)
sys.Dial("0017086839331@VoipCheap1",30)
sys.Dial("17086839331@VoipCheap1",30)
sys.Dial("17086839331@VoipCheap1",30)
sys.Respond(480, "#{sys.Username} Not available")
else
# Do your OUTGOING call processing customisations here.
case req.URI.User
when /^00/ then sys.Dial("1${dst:2}@VoipCheap1")
when /^1*/ then sys.Dial("VoipCheap1")
when /^00/ then sys.Dial("VoipCheap1")
else sys.Dial("VoipCheap1")
end
end
If I use VoipCheap's Soft Phone Cleint I Can Dial Out
By Using Just VoipCheap Client I Can Dial Out To LandLines, What I Want To Do Is Interegrate VoipCheap, and All My Other Providers, In MySipSwitch, For Incoming Calls Which is cool, but let say i want to make a outbound call, or if i don't answer the sip softphone, i want it to forward to my landline, or if i want to make a regular call to landline.
Both Mysipswitch and Sipsorcery will give you problems using these (betamax) providers, you will have no FUP, or service at all, in the worst case.
Last edited by TheFug on Tue Aug 24, 2010 9:24 pm, edited 1 time in total.
Thanks, The Fug.
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
I'm Not Getting What the FUP IS. Someone Please Explain?
I'm Not Getting What the FUP IS. Someone Please Explain what it is, and how it affects what i'm trying to do.
Fair Use Policy (use of free days)
These Betamax providers have a statement on their site,
and refer to "per unique IP address", which means you get only what they offer if you have your ata registered on your own IP or one that's only used by you once, and not many like yo do with online sipswitch services.
so running your own local version of MSS or SS on a private server, or your computer, (provided you manage that well through your router)
would solve that.
These Betamax providers have a statement on their site,
and refer to "per unique IP address", which means you get only what they offer if you have your ata registered on your own IP or one that's only used by you once, and not many like yo do with online sipswitch services.
so running your own local version of MSS or SS on a private server, or your computer, (provided you manage that well through your router)
would solve that.
Thanks, The Fug.
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D
gear: my ISP's Zyxel Modem/Router in bridge, Sitecom WL309 Router, Siemens Gigaset 301D